ENSONIQ ASR-10 Bedienerhandbuch PDF herunterladen (Seite 156)

Section 7 — Sampling/Signal Source Concepts

Easy Sampling 145

The available REC SRC Field 1 values are:

• INPUTDRY — This is the base setting, and it allows you to sample Audio Inputs dry (with no

effect). Audio Track A monitors the left channel of the REC SRC, and Audio Track B

monitors the right channel. You can hear how the dry signal will sound through the currently

selected effect as it is monitored on the Edit/(audio) Track OUT bus.

• INPUT+FX — This value allows you to sample Audio Inputs wet (with the currently selected

effect) on BUS1. All other voices are dry. Any WaveSamples, Instrument•Sequence Tracks or

Audio Tracks that were routed to BUS1, 2, or 3 will all show OUT=DRY- -FX BUS IN USE on

their Edit/Amp or Edit/Track, OUT bus screens.

When REC SRC= INPUT+FX, the ESP chip is dedicated to processing the Audio Inputs, and

the audio tracks monitor the direct output of the ESP chip. The left effects channel is

monitored on Audio Track A and the right channel on Audio Track B. The Wet/Dry mix is

set on the Edit/Effects page. Note that when the current effect is gain-dependent (for example

distortion or compression), the effect output may not sound the same as it would if REC SRC=

INPUTDRY. This happens because when the REC SRC= INPUT+FX, the audio input source is

routed directly into the effects processor at full level. To compensate, adjust the volume of the

external audio source.

• MAIN-OUT — This allows you to resample any ASR-10-generated audio routed to OUT

BUS1, 2, or 3. In VU mode, instruments can be Selected and Stacked in any combination

before sampling. The “pile” is playable from the keyboard, or via MIDI. You can also press

Play to start the sequencer and sample sequences and songs. The current effect also remains

unchanged. For the optimal signal-to-noise ratio, the Volume Slider should be at maximum

when sampling the MAIN-OUT.

Tip: When REC SRC= MAIN-OUT, you can use the volume slider in real time to sample volume fade-

ins and outs.

Tip: After sampling the MAIN OUT, the Edit/Amp BOOST parameter is automatically set to ON in

order to match the level between the original WaveSample and the resampled WaveSample. As a

final step, after you’re happy with the resampled results, you can futher optimize the

WaveSample by setting the Edit/Amp BOOST parameter to OFF, and performing the

Command/Amp NORMALIZE GAIN command.

• DIGITAL — Sample the Digital Input (requires the optional DI-10 Digital I/O interface). If no

digital interface is installed, this setting is not available.

The available REC SRC Field 2 values are:

• LEFT — Sample the LEFT channel of the REC SRC in MONO

• RIGHT — Sample the RIGHT channel of the REC SRC in MONO

• L+R — Sample both the LEFT and RIGHT channels of the REC SRC simultaneously in

STEREO

Using the Audio Tracks During Sampling

Pressing the Audio Track buttons will also change the REC SRC Field 2 value to reflect the

current combination of selected Audio Tracks. For instance, if you press the Audio Track A

button, the REC SRC Field 2 value changes to LEFT. If you press Audio Track B, the REC SRC

Field 2 value changes to RIGHT. If you press Audio Track A and while holding it down press

Audio Track B, the REC SRC Field 2 value changes to L+R. When both Audio Tracks are

selected (both yellow LEDs lit), holding one Audio Track button and pressing the other one will

change the REC SRC Field 2 value to LEFT. Both Audio Tracks will become Source Monitor

disabled (no red LEDs lit).

1 2 ... 151 152 153 154 155 156 157 158 159 160 161 ... 389 390

Kommentare zu diesen Handbüchern

Keine Kommentare

ENSONIQ ASR-10 Bedienerhandbuch Seite 156

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Digitale Klaviere ENSONIQ ASR-10