ENSONIQ ASR-10 Bedienerhandbuch Seite 118
- Seite / 390
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Section 6 — Effect Parameters
Edit/Effect Parameters 13
ROM-26 EQ + DELAY LFO
EQ + DELAY LFO features a stereo digital delay that provides LFO modulation of a wide range
of delays. This algorithm sounds great with an electric piano, but try it with any source!
EQ+DELAY LFO Signal Routing
BUS1 Left
BUS3 Left
BUS2 Left
BUS1 Right
BUS3 Right
BUS2 Right
EQ
R
Right
Delay
EQ
L
Main
Outputs
Left
Delay
Cross
Regen
Input Level Trim
LFO
Right
Delay
Input
(On/Off)
Regen
Regen
Damping
(LPF)
Damping
(LPF)
Output Level
The BUS1, BUS2, and BUS3 MIX parameters can be routed into the effect with different Dry/Wet
mixes.
The parameters available for this algorithm are:
DLY TIME L Range: 0 to 845 ms
This parameter determines the amount of time between the input signal and the left delay
output.
DLY TIME R Range: 0 to 845 ms
This parameter determines the amount of time between the input signal and the right delay
output. Set this differently from the left delay time to achieve dotted 1/8th note type effects.
LFO RATE Range: 0 to 99
This parameter controls the rate of pitch modulation which is the LFO. To achieve a chorusing
effect, this rate must be very slow.
LFO WIDTH Range: 0 to 99
This parameter controls the excursion of pitch modulation. Since the rate is usually very slow,
then the width is usually large.
L/R LFO Range: OUT-OF-PHASE or IN-PHASE
When this parameter is IN-PHASE, the left and right choruses will modulate their detunes
together. When set to OUT-OF-PHASE, the detune on the left channel will go up while the
detune on the right will go down.
DELAY REGEN Range: -99 to +99
This parameter controls the amount of regen (regeneration) applied to the delay time taps. The
sign of the value determines the polarity of the regen.
- Welcome! 1
- Amplification 6
- Backing-up the O.S. Disk 8
- An Important Note ix 9
- Accessories 9
- Warranty 9
- Need More Help? 10
- Monthly Magazines 11
- Rear Panel Connections 12
- 2 Rear Panel Connections 13
- Rear Panel Connections 3 14
- Control Voltage Foot Pedal 14
- 4 Rear Panel Connections 15
- Rear Panel Connections 5 16
- Front Panel Controls 17
- Parametric Programming 18
- 8 Front Panel Controls 19
- FILE 2 GRAND PIANO 19
- Front Panel Controls 9 20
- Performance Controllers 21
- About Pressure 11 22
- Pressure (After-touch) 22
- Architecture 23
- About Memory 13 24
- Warning! 24
- Purchasing SIMMs 24
- Move jumper when 25
- MEM EXP JMP 25
- 18 About Memory 29
- About Instruments 30
- 20 About Instruments 31
- About Banks 32
- 22 About Banks 33
- Playing Instruments 23 34
- 24 Keyboard Range 35
- Instrument #2 — Bass 35
- Instrument #1 — Piano 35
- 26 About the Sequencer 37
- Saving Sequencer Data 39
- Managing Your System Headroom 41
- Managing Headroom 31 42
- Audio Track Headroom 42
- Parameter Illustrations 43
- Section 2 — System•MIDI 44
- 2 Edit/System•MIDI Parameters 45
- PEDAL (VOLUME / MOD) 45
- Edit/System•MIDI Parameters 3 46
- LEFT FOOT SW 46
- AUTO-LOOP FINDING (ON/OFF) 46
- MIDI Parameters 47
- Edit/System•MIDI Parameters 5 48
- MIDI IN MODE 48
- 6 Edit/System•MIDI Parameters 49
- MONO Modes 49
- MIDI CONTROLLERS (ON/OFF) 49
- Edit/System•MIDI Parameters 9 52
- MULTI CONTROLLERS 52
- ENTER PLAYS KEY 52
- Command/System•MIDI Page 53
- System•MIDI Commands 11 54
- COPY O.S. TO DISK 54
- 12 System•MIDI Commands 55
- SAVE GLOBAL PARAMETERS 55
- LOAD GLOBAL PARAMETERS 55
- CREATE DIRECTORY 55
- System•MIDI Commands 13 56
- CHANGE STORAGE DEVICE 56
- SAVE MACRO FILE 56
- COPY FLOPPY DISK 56
- 14 System•MIDI Commands 57
- MIDI SYS-EX RECORDER 57
- LOAD MIDI 58
- FILE 1 - SYS-EX FILE 58
- 16 System•MIDI Commands 59
- COPY SCSI DRIVE 59
- SCSI Drive Hook-Up 59
- 18 System•MIDI Commands 61
- INSERT NEXT BACKUP DISK 61
- System•MIDI Commands 19 62
- INSERT DISK #1 62
- Notes About BACKUP/RESTORE 62
- 20 System•MIDI Commands 63
- FORMAT SCSI DRIVE 63
- About Macros 23 66
- Invoking a Direct Macro 66
- Instruments 67
- 2 About Instruments and Banks 68
- 4 About Instruments and Banks 70
- To Load a Bank 70
- FILE 4 SOUND BANK 1 70
- Performance Presets 72
- About Performance Presets 7 73
- Creating a Performance Preset 73
- PRESET NUMBER=1 *UND* 73
- 8 About Performance Presets 74
- Edit/Instrument Page 75
- 2 Edit/Instrument Parameters 76
- Programming Patches 76
- Edit/Instrument Parameters 3 77
- KEYDOWN LAYERS 77
- KEYUP LAYERS 77
- MIDI OUT CHANNEL 77
- 4 Edit/Instrument Parameters 78
- MIDI OUT PROGRAM 78
- PRESSURE MODE 78
- Edit/Instrument Parameters 5 79
- MIDI STATUS 79
- Edit/Instrument Parameters 7 81
- INST (Key) RANGE 81
- XPOS OCT - SEMI (Transpose) 81
- Command/Instrument Page 82
- Command/Instrument Page 9 83
- SAVE INSTRUMENT 83
- SAVE BANK 83
- Command/Instrument Page 11 85
- DELETE INST EFFECT 85
- Section 5 — Effect Concepts 86
- INST (Instrument) Effects 87
- BANK Effect 87
- ROM Effect 87
- Selecting Effects 88
- Instruments and Banks 90
- 6 Selecting Effects 91
- Programming Effects 92
- 8 Selecting Effects 93
- Single Function Effect Mixer 93
- Dual Function Effect Mixer 93
- Selecting Effects 9 94
- Triple Function Effect Mixer 94
- Selecting Effects 11 96
- Edit/Effects Page 98
- ROM-01 HALL REVERB 98
- ROM-02 44KHZ REVERB 98
- ROM-03 ROOM REVERB 98
- ROM-04 DUAL DELAYS 99
- ROM-05 44KHZ DELAYS 99
- ROM-06 CHORUS+REVRB 99
- ROM-07 PHASER+REVRB 100
- ROM-08 FLANGER+REV 101
- ROM-09 ROT. SPKR+REV 101
- ROM-10 CHOR+REV+DDL 102
- ROM-11 CMP+DIST+REV 103
- CMP+DIST+REV Signal Routing 103
- ROM-12 DIST+CHO+REV 104
- ROM-13 WAH+DIST+REV 105
- ROM-14 SMALL ROOM 106
- ROM-15 LARGE ROOM 106
- ROM-16 HALL REVERB2 106
- 2 Edit/Effect Parameters 107
- ROM-17 SMALL PLATE 108
- ROM-18 LARGE PLATE 108
- 4 Edit/Effect Parameters 109
- ROM-19 REVRSE REVRB 110
- ROM-20 REVRSE REVB2 111
- ROM-21 GATED REVERB 112
- 8 Edit/Effect Parameters 113
- Section 6 — Effect Parameters 114
- Edit/Effect Parameters 9 114
- ROM-22 NLIN REVRB 1 115
- ROM-23 NLIN REVRB 2 115
- ROM-24 NLIN REVRB 3 115
- Edit/Effect Parameters 11 116
- ROM-25 MULTITAP DDL 117
- ROM-26 EQ + DELAY LFO 118
- 14 Edit/Effect Parameters 119
- ROM-27 VCF+DISTORT 120
- ROM-28 GUITAR AMP 1 121
- ROM-29 GUITAR AMP 2 121
- Edit/Effect Parameters 17 122
- ROM-30 GUITAR AMP 3 123
- Edit/Effect Parameters 19 124
- ROM-31 SPKR CABINET 125
- ROM-32 TUNABLE SPKR 125
- ROM-33 EQ+CHOR+DDL 126
- 22 Edit/Effect Parameters 127
- ROM-34 EQ+VIBR+DDL 128
- 24 Edit/Effect Parameters 129
- ROM-35 EQ+FLNGR+DDL 130
- 26 Edit/Effect Parameters 131
- ROM-36 EQ+TREM+DDL 132
- ROM-37 PHASER+DDL 133
- Edit/Effect Parameters 29 134
- Phaser+DDL Signal Routing 134
- ROM-38 8-VOICE CHOR 135
- ROM-39 PITCH SHIFT 136
- 32 Edit/Effect Parameters 137
- ROM-40 PITCH+DDL 138
- ROM-41 FAST PITCHSH 139
- ROM-42 EQ+CMPRESSOR 140
- 36 Edit/Effect Parameters 141
- Edit/Effect Parameters 37 142
- ROM-43 EXPANDER 143
- ROM-44 KEYED EXPNDR 144
- 40 Edit/Effect Parameters 145
- ROM-45 INVRS EXPNDR 146
- ROM-46 DE-ESSER 147
- Edit/Effect Parameters 43 148
- ROM-47 DUCKER 149
- Edit/Effect Parameters 45 150
- ROM-48 RUMBLE FILTR 151
- ROM-49 PARAM EQ 151
- ROM-50 VAN DER POL 152
- What is Sampling? 153
- What is Sampling? 143 154
- Sample Rate 154
- Aliasing 154
- Getting Ready to Sample 155
- Easy Sampling 155
- Easy Sampling 145 156
- 146 Easy Sampling 157
- PICK SAMPLE INSTRUMENT 157
- Level-Detect 157
- (or VU) Mode: 157
- Easy Sampling 147 158
- Setting the Input Level 158
- RECORDING xxx SEC LEFT 158
- 148 Easy Sampling 159
- PLAY ROOT KEY OR ENTER 159
- Normalizing Gain 159
- Default Output Routings 159
- MultiSampling 160
- Stereo Sampling 162
- Companion Layers 163
- STEREO LAYER LINK=ON 163
- Looping 153 164
- Auto-Loop Finding 164
- Short (Single-Cycle) Loops 165
- 154 Looping 165
- Looping 155 166
- Adjusting Loop Position 166
- Long Loops 166
- 156 Looping 167
- Sampling Parameters 168
- 2 Sampling Parameters 169
- SAMPLE RATE 169
- PRE TRIGGER 169
- Sampling Parameters 3 170
- SAMPLE TIME 170
- 4 Sampling Parameters 171
- SELECT A STEREO LAYER 171
- About WaveSamples 172
- 2 WaveSample Configuration 173
- About WaveSamples 3 174
- WaveSample Commands 175
- Modulators 176
- 6 Modulators 177
- Modulation Sources 177
- Modulators 7 178
- 8 Modulators 179
- Modulators 9 180
- Edit/Wave Page 181
- Loop Parameters 182
- Edit/Wave Page 3 183
- MOD / SRC 183
- MOD AMT / RANGE 183
- 4 Edit/Wave Page 184
- Command/Wave Page 185
- About Loop Commands 186
- Command/Wave Page 7 187
- CROSS FADE LOOP 187
- 8 Command/Wave Page 188
- REVERSE CROSS FADE 188
- ENSEMBLE CROSS FADE 188
- Command/Wave Page 9 189
- BOWTIE CROSS FADE LOOP 189
- 10 Command/Wave Page 190
- BIDIRECTIONAL X-FADE 190
- Command/Wave Page 11 191
- COPIES WILL CHANGE-OK? 191
- MAKE LOOP LONGER 191
- 12 Command/Wave Page 192
- SYNTHESIZED LOOP 192
- 14 Command/Wave Page 194
- COPY WAVE PARAMETERS 194
- About Mix, Merge, and Splice 196
- 1st WaveSample 2nd WaveSample 197
- 2nd WaveSample 197
- Command/Amp Page 19 199
- FADE OUT 199
- Before: After: 199
- REPLICATE DATA 201
- Command/LFO Page 23 203
- SCALE DATA 203
- Edit/Pitch Page 204
- Command/Pitch Page 205
- Pitch Commands 3 206
- 4 Pitch Commands 207
- COPY PITCH TABLE 207
- DELETE PITCH TABLE 207
- EXTRAPOLATE PITCH TBL 207
- ASR-10 Filters 208
- Edit/Filters Page 209
- Edit/Filters Parameters 7 210
- Edit/Amp Page 211
- Edit/Amp Parameters 9 212
- A - B FADE IN - TO 212
- C - D FADEOUT - TO 212
- 10 Edit/Amp Parameters 213
- FADECURVE 213
- OUT (Output Routing) 213
- ASR-10 Envelopes 214
- HARD VEL LEVELS 215
- SOFT VEL LEVELS 215
- 2ND RELEASE (TIME) - LEV 216
- ATTACK TIME VEL AMT 217
- KBD TIME SCALING 217
- SOFT VEL CURVE 217
- ENVELOPE MODE 218
- ENVELOPE (Envelope Template) 218
- Envelope Templates 219
- Edit/LFO Page 220
- Edit/LFO Parameters 19 222
- LFO MODE 222
- DEPTH MOD - AMOUNT 222
- RATE MOD - AMOUNT 222
- Edit/Layer Page 223
- GLIDE MODES 224
- Edit/Layer Parameters 23 226
- STEREO LAYER LINK 226
- Command/Layer Page 227
- Sequencing on the ASR-10 228
- Compare this to an 228
- Record Stop 230
- Continue 230
- 4 Sequencer Basics 231
- Important: 231
- Sequencer Basics 5 232
- Selecting a Sequence/Song 233
- Playing a Sequence/Song 233
- Sequence Tracks 234
- Creating a New Sequence 234
- Recording a Sequence 235
- Recording a Sequence 9 236
- “Punching In” on a Track 236
- 10 Recording a Sequence 237
- Additional Notes 237
- To additional 238
- MIDI devices 238
- 12 Recording a Sequence 239
- Recording MIDI Tracks 239
- Recording a Sequence 13 240
- Recording Program Changes 240
- 14 Recording a Sequence 241
- Song Mode 242
- 16 Song Mode 243
- Song Mode 17 244
- Song Tracks 245
- Song Mode 19 246
- 20 Song Mode 247
- About Audio Tracks 248
- 22 About Audio Tracks 249
- About Audio Tracks 23 250
- Types of Audio Tracks 251
- About Audio Tracks 25 252
- Song Audio Tracks 252
- All About Memory 253
- About Audio Tracks 27 254
- Memory Fragmentation 254
- RAM Buffers 254
- 1. Select the sample rate 255
- 2. Configure the Audio Tracks 255
- 3. Choose a Record Source 255
- 4. Prepare the Audio Tracks 255
- About Audio Tracks 29 256
- Step Two 256
- 30 About Audio Tracks 257
- About Audio Tracks 31 258
- 32 About Audio Tracks 259
- About Audio Tracks 33 260
- 34 About Audio Tracks 261
- Step Three 261
- : Choosing a Record Source 261
- INPUT+FX Signal Chain Routing 263
- MAIN-OUT Signal Chain Routing 264
- 38 About Audio Tracks 265
- Step Four 265
- : Preparing Audio Tracks 265
- About Audio Tracks 39 266
- IF: THEN: 266
- Audio Tracks in “Chain Play”: 266
- 40 About Audio Tracks 267
- Which Track is Selected? 267
- Tie the Jack to the Track 267
- Overdubbing 268
- 42 About Audio Tracks 269
- Amalgamation 269
- About Audio Tracks 43 270
- 44 About Audio Tracks 271
- About Audio Tracks 45 272
- 46 About Audio Tracks 273
- Bounce-Down 274
- 48 About Audio Tracks 275
- Notes on Bounce-down: 275
- Song Audio Track Mixdown 276
- Caution: 277
- About Audio Tracks 51 278
- System Optimization Tips 279
- AudioSample Specs 279
- About Audio Tracks 53 280
- 54 About Audio Tracks 281
- About Audio Tracks 55 282
- The Edit/Seq•Song Page 283
- Edit/Seq•Song Parameters 3 285
- SEQ COUNTOFF 285
- SEQ REC MODE 285
- Command/Seq•Song Page 287
- 6 Seq•Song Commands 288
- SAVE SONG AND ALL SEQS 288
- RENAME SONG/SEQUENCE 288
- SEQUENCER INFORMATION 288
- Seq•Song Commands 7 289
- ERASE SONG + ALL SEQS 289
- APPEND SEQUENCE 289
- CHANGE SEQUENCE LENGTH 289
- 8 Seq•Song Commands 290
- EDIT SONG STEPS 290
- Seq•Song Commands 9 291
- ERASE ALL AUDIOSAMPLES 291
- SET SONG ATRK PLAYBACK 291
- Edit/(sequence) Track Page 292
- Edit/Track Parameters 11 293
- MIX - PAN 293
- Track MIX 293
- 12 Edit/Track Parameters 294
- Track PAN 294
- EFFECT MOD CONTROL 294
- Edit/Track Parameters 13 295
- MULTI-IN MIDI CHAN 295
- Edit/(audio) Track Page 296
- 16 Audio Track Parameters 298
- ASMPLNAME (AudioSample Name) 298
- Command/Track Page 299
- 18 Track Commands 300
- ERASE/UNDEFINE TRACK 300
- FILTER EVENT 300
- * * * * * * 301
- BEATCMD CLOCKBAR 302
- Track Commands 21 303
- Event Location 303
- CMD CLOCKBAR 304
- Track Commands 23 305
- SCALE EVENT 305
- SHIFT TRACK BY CLOCKS 305
- Command/(audio) Track Page 306
- Track Commands 25 307
- ERASE AUDIO TRACK 307
- SHIFT AUDIO TRACK 307
- Track Commands 27 309
- AUDIOSAMPLE INFO 309
- 28 Track Commands 310
- FILTER AUDIO EVENTS 310
- Section 14 — Storage 311
- 2 Disk Storage 312
- ASR-10 Disk Functions 313
- 4 Disk Functions 314
- Loading an Instrument 315
- INST STOP 316
- STOPINST 318
- Sequencer Data Storage 9 319
- 10 Sequencer Data Storage 320
- 12 Loading and Saving Effects 322
- Loading an Effect File 322
- Saving an Effect to Disk 322
- Deleting a File from Disk 323
- Audio Track Storage 324
- 16 Audio Track Storage 326
- 18 Audio Track Storage 328
- Deleting: 328
- MIDI Sys-Ex 19 329
- System Exclusive Storage 329
- 20 MIDI Sys-Ex 330
- MIDI Sys-Ex 21 331
- System Exclusive Messages 331
- ASR-10 Disk Messages 332
- Disk Messages 23 333
- Resampling through an EQ 1 334
- Record a Dry Sample 334
- 2 Resampling through an EQ 335
- Resampling through an EQ 3 336
- Resampling with Effect 336
- 4 Resampling through an EQ 337
- Resampling through an EQ 5 338
- 6 Resampling through an EQ 339
- Applications 1 340
- Creating Keyboard Cross Fades 341
- Applications 3 342
- 4 Applications 343
- 2 MIDI Connections 346
- Creating a MIDI Instrument 346
- SQ-R PLUS 32 Voice 346
- Making a MIDI Instrument 3 347
- 4 MIDI Sequencer Applications 348
- MIDI InMIDI Thru 349
- MIDI Out 349
- MIDI Thru 349
- 6 MIDI Sequencer Applications 350
- Using MONO A Mode 352
- Using MONO B Mode 353
- Converter 353
- Patch Selects and Presets 354
- Song Position Pointers 355
- Delay Times/Tempo BPM Chart 356
- An Audio Track Tutorial 361
- An Audio Track Tutorial 5 362
- 6 An Audio Track Tutorial 363
- KEEP = OLD NEW 363
- 8 An Audio Track Tutorial 365
- An Audio Track Tutorial 9 366
- Appendix 367
- 44EQ+DDL 368
- 44DDL+CH+REV 369
- 44DDL+CHORUS 370
- 44DLYLFO+REV 371
- 44EQ+DDL+CHO 372
- 44PARAM EQ 372
- 44EQ+REVERB 373
- 44ROTO+REVRB 374
- 44EQ+ROT+DDL 375
- Additional Effect Parameters 381
- ASR-10 MIDI Implementation 382
- Registered Parameters 382
- MIDI Implementation XVII 383
- Version: 2 383
- Conversion Table 243 387
Verwandte Produkte und Handbücher für Digitale Klaviere ENSONIQ ASR-10
(154 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern